A Step-by-Step Guide to Installing a Bath Tub
A Step-by-Step Guide to Installing a Bath Tub
Blog Article
We've found this great article about Tools You Need to Install a New Bathtub below on the internet and thought it made good sense to write about it with you over here.
Installing a tub isn't specifically rocket science, yet it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately challenging task. If the old tub is easily obtainable, the job can relocate quickly; if you need to open a wall surface to remove the old bathtub and also place the new bath tub, the job is much harder. In either situation, the project is within a residence handyman's skills, although you will certainly need an assistant to move out the old bathtub and embeded in the new one. See to it you have certified yourself for the work as well as fit attempting it. As opposed to hiring a specialist to take control of a halfway-completed job, it is far better to consider using one before you start. Chances are you may require a professional plumber to make tube links.
This article will certainly aid you set up a brand-new bathtub in your shower room if you have actually already purchased a brand-new tub as well as do not need to alter the setup of your previous supply of water pipelines.
Your devices and product checklist must consist of the following:
Getting ready for the Installment
Firstly, the supporting framework provided with the bath needs to be fitted (if required) according to the producer's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to avoid stress on the tub.
Fit the adaptable faucet ports to the bottom of the two faucets utilizing 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize every one of the provided washers.
Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last setting.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is detach the supply of water. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing taps can be quite problematic as a result of the limited gain access to that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will certainly come from the pipes. As soon as the supply pipelines have actually been gotten rid of, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from transforming throughout this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Prior to proceeding to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Installing the Bath tub
Utilizing the two wood boards under its feet, place the bath tub in the needed position. The wood boards are useful in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four small factors.
The next objective is to ensure that the bath tub is leveled all round. This can be accomplished by examining the spirit level and also adjusting the feet on the bath tub until the level reads degree.
To install faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipe by making a compression join; after that do the very same for the other tap.
Activate the water system and inspect all joints and new pipework for leakages as well as tighten them if necessary. Fill the tub as well as likewise inspect the overflow electrical outlet and the regular electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub ought to wait till the bathtub has been made use of at least when as this will certainly settle it into its last position.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and the other end offers a link to the current supply pipelines.
If you require to fit a monobloc, after that you will call for lowering couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the faucet in the installing opening in the bath/basin making sure that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the supplier supplied backnut. When the tap is securely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical tap ports. The former type ought to be connected to the tap ends first, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bathroom meets the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split a stiff seal, triggering the water to penetrate the wall in between the bathroom as well as the tiling, resulting in problems with wetness and also possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and also cartridges, as well as are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill the bath tub with water before sealing, to permit the motion experienced when the tub remains in use. The sealant can split relatively early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally quickly offered on the market. It is a good idea to fit the ceramic tiles using waterproof or water resistant glue and cement.
Bathtub Installation
How Important Is A Bathtub To Your Home?
High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.
Install Piping Before Tub
You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.
Position the Tub
Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.
NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.
Assemble Drain Connections
Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.
Place a Pipe For the Shower Head
First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.
Attaching Hot and Cold Water Lines
Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.
Install the Spout
Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.
NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.
Check For Leaks
Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.
estore the Bathroom Wall
Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.
https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/
As an enthusiastic person who reads on How to Install a Bathtub, I was thinking sharing that article post was valuable. In case you enjoyed reading our article please make sure you remember to share it. Thanks so much for your time spent reading it.
Book Now!
Report this page